Electrician updating the panel and wiring during a whole-home remodel in Arlington TX
11 min read

Should You Update Old Wiring in a Remodel? Arlington, TX

Drive along Glasgow Drive or Colorado Lane, a few blocks from Gunn Junior High School, and you’ll see street after street of single-story brick homes from the 1960s and 1970s. Plenty of them still run on the wiring they were built with. That isn’t a crisis on its own, but if you’re about to open up walls for a remodel in this part of Arlington, the electrical system is the one thing you don’t want to close back up without a proper look.

Quick answer: In most older Arlington homes, yes, at least for the rooms you’re touching. A remodel is the one time the walls, ceilings and attic are already open, so updating those circuits costs far less than doing it after the drywall goes back on. For a typical whole-home project around the 76015 area, the electrical work often adds a few days to about a week, depending on the panel and branch wiring.

Key Takeaways: Should You Update Old Wiring in a Remodel

  • Open walls are the moment: rewiring the rooms in a remodel costs a fraction of what the same work costs once the finishes are in.
  • Age is normal here: NAHB analysis of Census data puts the typical owner-occupied U.S. home at roughly 40 years old, so original wiring is common.
  • Watch for the signs: two-prong outlets, warm cover plates, tripping breakers and a panel under 100 amps all point toward an update.
  • Permits apply: electrical changes inside a remodel are permitted and inspected through the City of Arlington, and your contractor handles that.
  • Texas attics are hard on wire: decades of summer heat can dry out the insulation on old cable, so the attic runs get checked first.
Single-story brick ranch home typical of older Arlington neighborhoods
Many homes near Glasgow Drive date from the 1960s and 1970s and still carry their original wiring. (Photo by Danny Meneses on Pexels)

What wiring do older Arlington homes usually have?

Most homes built here between the early 1960s and early 1980s have copper wiring in plastic-sheathed cable, but a real share from the late 1960s and early 1970s have aluminum branch wiring, and nearly all of them have far fewer circuits than a modern household uses.

Aluminum branch wiring showed up nationwide for a few years when copper prices spiked. The wire itself isn’t the problem. The connections are. Aluminum expands and contracts more than copper, so terminals at outlets and switches can loosen over the decades, and loose connections run hot. Electricians have proven fixes, and a remodel is a sensible time for them.

Many homes in this part of Arlington, along Florida Drive and the streets around California Lane Park, sit on slab foundations, so almost every wire runs through the attic rather than under the floor. That’s convenient for access. It also means the cable has spent fifty summers in attic temperatures that regularly pass 120 degrees, which is a big reason we recommend a look before any home remodeling service in Arlington gets underway.

How do you know if your wiring needs updating?

You usually can’t tell from the living room, but a handful of signs are easy to spot, and it’s worth noting them before your in-home estimate so the conversation starts in the right place.

  • Two-prong outlets: no ground means no safe place for surge protectors or most modern electronics.
  • Warm or discolored cover plates: heat at a device points to a loose or overloaded connection behind it.
  • Breakers that trip often: especially when the microwave and toaster run together, which tells you the kitchen shares a circuit.
  • Lights that dim when the AC starts: often a sign the service or the panel is working at its limit.
  • A full panel with no spare slots: any new circuit for the remodel has nowhere to land.
💡 Good to know: Take a photo of the inside of your panel door before the estimate. The brand, the main breaker rating and the number of open slots tell an experienced project manager a lot in about ten seconds.
Older residential breaker panel with no spare slots
A full panel with no open slots is one of the clearest signs an update belongs in the remodel. (Photo by ranjeet . on Pexels)

Does a remodel need a permit for electrical work in Arlington?

In general terms, yes. Adding circuits, relocating outlets, replacing a panel or rewiring a room inside a remodel is work the City of Arlington permits and inspects, and the contractor handles the paperwork and schedules the inspections as part of the job.

An inspector visits after the rough-in, before the drywall goes up, and again at the end once the devices and panel are finished. If something isn’t right, it gets corrected before the walls close.

Requirements vary from city to city and change over time, so treat anything you read online, including this, as a starting point rather than a rulebook. Southern Home Remodeling is insured as required by the cities for permits, and project manager John Tavera keeps the inspection schedule inside the overall timeline so it doesn’t hold up the next trade.

What does the electrical update process look like?

Electrical work inside a remodel follows the same rhythm as the rest of the project, described in more detail on our remodeling process page. Here’s how it typically runs in an older Arlington home.

1
Walkthrough and panel checkDuring the free in-home estimate we look at the panel, open a few outlets in the rooms you’re remodeling and check the attic. That tells us whether it’s a few circuits or a bigger rewire.
2
Plan circuits around the new layoutOutlets, switches, lighting and appliance circuits get drawn onto the remodel plan. This is where you decide on under-cabinet lighting, an island outlet or a line for a future EV charger.
3
Rough-in while the walls are openAfter demolition, the electrician runs new cable, sets boxes and, if needed, replaces the panel. In a slab home this is mostly attic work, so it moves quickly.
4
Rough-in inspectionThe city inspector checks the work before insulation and drywall. Nothing gets covered until that visit is passed.
Southern Home Remodeling
Thinking about Home Remodeling?
Skip the guesswork. Our team gives you a clear, no-pressure plan and a free in-home estimate for Home Remodeling in Arlington, TX.
5
Devices, fixtures and final inspectionOnce paint and tile are done, outlets, switches, fans and fixtures go in, the panel gets labeled, and the final inspection closes out the permit.
★ Trusted In-Home Design & Remodeling Contractors

Ready to Update the Wiring in Your Arlington Remodel?

If your home near Gunn Junior High School still has its original panel and two-prong outlets, we can fold the electrical update into your remodel plan and handle the City of Arlington permits for you.

Get a Free Estimate ➞ Call (817) 330-9499 ➞

Which electrical upgrades matter most during a remodel?

Kitchens and bathrooms come first, because that’s where the rules have changed the most since the 1970s and where today’s appliances pull the most power. If you’re already planning kitchen and bath remodeling in Arlington, most of the items below come along naturally.

Upgrade Where it matters Why do it mid-remodel Priority
GFCI protection Kitchen, baths, garage, outdoors Boxes are open, easy swap High
Dedicated appliance circuits Kitchen New cable runs with the layout High
Grounded three-prong outlets Every remodeled room Needs new cable, walls open High
Panel upgrade Whole house One shutdown instead of two Medium to high
Bath exhaust fan circuit Bathrooms Ceiling is open for ducting Medium
EV or workshop circuit Garage Panel work already scheduled Optional
Electrician running new cable through open framing during a remodel
Rough-in happens while the walls are open, before insulation and drywall. (Photo by La Miko on Pexels)

How does Texas attic heat affect old wiring?

Heat ages the plastic insulation on cable the way it ages a garden hose left in the sun: slowly, then all at once. Many homes in this part of Arlington have attics that sit well above 120 degrees for months every year, and after a few decades the outer jacket on old cable can turn brittle and crack where it bends over a joist.

Crews also find junction boxes with no covers, splices made outside a box entirely, and cable buried under blown-in insulation where nobody has looked in forty years. None of that is visible from inside the house. All of it is visible the day the attic gets inspected during a remodel, which is why the attic walk is part of our first visit.

💡 Good to know: If attic insulation is on your remodel list, schedule it after the electrical rough-in and inspection. Insulating first means the electrician has to dig through it, and some of it ends up on your garage floor.

Should you upgrade the panel at the same time?

If your panel is rated under 100 amps, has no spare slots, or is one of the older brands electricians routinely flag, a remodel is usually the right time to replace it. Doing it mid-project means one scheduled power shutdown instead of two, and the new circuits land in a panel that has room for them.

Most homes built today get 200-amp service, and that’s the common target for an older home adding central air, a tankless water heater, an induction cooktop or an EV charger. Whether your house actually needs it depends on the loads you’re adding, and that’s a calculation for the electrician, not a guess from a blog post. Sometimes a 100-amp panel with a modern breaker layout is plenty.

A service upgrade often involves the utility and a short outage, so we schedule it for a day when nothing else on site needs power. Small details like that separate a smooth home remodeling project from a frustrating one.

★ Trusted In-Home Design & Remodeling Contractors

Planning a Whole-Home Remodel in Arlington?

Tired of breakers tripping every time the microwave runs? A remodel is the right moment to fix it. Book a free in-home estimate and we will check the panel and attic on the first visit.

Get a Free Estimate ➞ Call (817) 330-9499 ➞

What homeowners near Gunn Junior High School usually run into

Crews working the streets between Gunn Junior High School and H.A.D. Dunsworth Park see the same handful of situations over and over. The most common is layered wiring: an original 1970s system, a partial update from the 1990s when somebody redid the kitchen, and a few DIY circuits added since. Each layer was fine on its own. Together they make a panel nobody can read.

Second is the bathroom with no GFCI protection at all. Updating that is routine, and it’s part of every bathroom we touch. You can see how this plays out in an older house in our 1960s home remodel in Bedford, where the wiring got the same attention as the shower.

Last is the home where a previous owner replaced the panel but left the aluminum branch circuits untouched. A new panel on old aluminum connections solves the wrong problem. A proper walkthrough catches it, and the fix is well understood.

Attic wiring and junction boxes in a Texas slab home
In slab homes around Arlington nearly every circuit runs through the attic. (Photo by Magda Ehlers on Pexels)
💡 Good to know: Ask for a labeled panel schedule at the end of the job. It’s a two-minute task for the electrician and it will save the next tradesperson, or the next owner, hours of guessing.

Planning Your Remodel in Arlington?

If your home near Glasgow Drive or California Lane Park still runs on its original wiring, the smartest move is to fold the electrical update into the remodel you’re already planning. Our office at 1611 W Sanford St near downtown Arlington is about 5 km away, roughly a three-mile drive, so the first visit is an easy one to schedule.

Southern Home Remodeling is owner-run and led by owner Cristian Quimbayo, who has been building across DFW since 2011 and operating as Southern Home Remodeling since 2016. The team brings more than 40 years of combined experience in construction and construction lending, and every project comes with a 12-month workmanship warranty, with manufacturers covering the products. We’re rated on Google and we work with a satisfaction-guarantee approach.

★ Trusted In-Home Design & Remodeling Contractors

Get a Free Remodeling Estimate in Arlington

Homes around California Lane Park deserve wiring that matches how you live today. Schedule your free in-home estimate and get a clear plan before any wall comes down.

Get a Free Estimate ➞ Call (817) 330-9499 ➞

Take a look at what our home remodeling contractors in Arlington handle on a typical project, then book a free in-home estimate. The office is open Monday through Saturday, 8AM to 6PM, and the remodeling services in Arlington page is the quickest place to start.

Southern Home Remodeling
Get Your Free Home Remodeling Estimate in Arlington, TX
Owner-run and building across DFW since 2011. Book a free in-home estimate today, honest pricing, quality craftsmanship, and a team that shows up when they say they will.

FAQ

Is aluminum wiring in a 1970s home dangerous?

Not automatically, but the connections at outlets and switches can loosen over time and run hot. Electricians handle it either by replacing the runs or by using rated connectors at every device. A remodel is a practical time to do either, because the walls and attic are already open and the work is inspected.

Do I need to rewire the whole house during a remodel?

Usually not. In most projects the circuits serving the remodeled rooms get updated, the panel is checked, and any obvious attic problems are corrected. A full rewire is reserved for homes with widespread damage or very old cable. The in-home estimate is where that call gets made, room by room.

How long does electrical work add to a remodel in Arlington?

For a typical whole-home remodel around the 76015 area near Gunn Junior High School, electrical updates often add a few days to about a week, including the rough-in inspection. A full panel replacement or a service upgrade through the utility can add a little more, depending on scheduling and scope.

Will the power be off during the work?

Only briefly. Individual circuits are switched off while they are being worked on, and a panel replacement typically needs one planned shutdown of several hours. We schedule it for a day when no other trade needs power on site, and we let you know in advance so you can plan around it.

Does a panel upgrade require a permit?

In general terms, yes. Replacing a panel or upgrading the electrical service is work the City of Arlington permits and inspects, and the contractor handles the application and the inspections. Requirements vary between cities and change over time, so a professional assessment at the estimate is the reliable way to confirm what applies.

Home Remodeling help near Arlington

Southern Home Remodeling works throughout Arlington, including the Arlington area around Glasgow Drive and Colorado Lane, near California Lane Park and H.A.D. Dunsworth Park. Projects in 76015 are permitted and inspected through the City of Arlington, and our team handles that paperwork as part of the job.

Our office at 1611 W Sanford St, Arlington, TX 76012 is about 3.1 miles from Arlington, so an in-home estimate is easy to schedule. Call 817-330-9499 or use the estimate button below.

Service page for this area: Home Remodeling in Arlington. City guide: home remodeling in Arlington.

Keep exploring

Free in-home estimate

Planning a remodel like this one?

Owner Cristian Quimbayo walks your home, explains your options and gives you a written quote. No pressure, no obligation.

Rated on Google | Mon to Sat, 8AM to 6PM
Scroll to Top